Showing posts with label to. Show all posts
Showing posts with label to. Show all posts
Wednesday, March 5, 2014
How to Remove Old Finish From Furniture
By [http://ezinearticles.com/?expert=Kenneth_J_Ellis]Kenneth J Ellis
General Rules for Removing Old Finish
1. Do nothing that will harm the original surface unless the piece is to be painted.
2. If you plan to replace the old finish with a clear type, all old finish must be removed so the new will hold properly.
3. When removing old paint it is not only permissible but acceptable to most collectors that the marks of wear through the years, as well as traces of color from the old paint be allowed to remain so that they will show through the new finish. Traces of old paint add interest to the piece by their variations of color, and are evidence of age. Old paint however, should not be left on in thick patches or blotches.
4. For final cleaning, after using a remover, use a cabinet scraper or knife blade on joints, corners, and angles on flat surfaces. Use steel wool to clean out carvings, turnings, mouldings etc.
5. If the old finish is shellac, you dont need a paint and varnish remover. It can be taken off with denatured alcohol and steel wool.
Selecting Your Paint Remover
Commercial removers are solvents rather than corrosives. They act more slowly on older paints than on new, but they are the only materials that can be used safely. They attack the material such as linseed oils used in paint, or the resins in shellac, varnish, and lacquer. It wont injure a surface by burning it or leaving marks and wont be harmful to glue or raise the grain of the wood. They contain no water and may be used on veneered surfaces without causing the veneer to loosen. When used properly and washed off, solvent-type paint removers leave the surface clean. Dislodging layers of old paint or varnish isnt difficult, but patience, time, and-following the directions on the container are required.
How to Remove Old Finishes
Dislodging layers of old paint or varnish isnt difficult, but it takes patience, time, ans perseverance. Here are some basic directions for using paint remover.
1. Place the piece to be worked on over layers of old newspaper in good strong light, and if possible, with the top surface in a horizontal position. Avoid working in cold temperatures below 68 degrees F--cold slows down the action of removers.
2. Shake the remover thoroughly, pour a small amount into a small can and apply thickly with a full brush in one direction. Do not rebrush.
3. Let the remover stand for a period of from 10 to 20 minutes, or until the paint or varnish lifts.This is indicated by a crinkling of the surface. Do not let the remover dry. If it begins to dry, apply an additional coat and wait for it to act.
4. When the surface covering has lifted, remove it with a dull putty knife that has the corners rounded off. Remove the accumulation of remover and finish and wipe the knife on a piece of old newspaper.
5. Wipe off as much of the remaining finish as possible using burlap squares.
6. Scrub the surface with a small brush dipped in denatured alcohol.
7. Wipe off with several clean cloths.
8. Rub the surface with steel wool dipped in denatured alcohol.
9. Wipe with cloths dipped in alcohol. This not only cleans the traces of remover from the surface but neutralizes its further action. Follow by wiping with clean cloths dipped in turpentine or paint thinner.Then wipe with dry rags. This will remove any remaining wax or silicone polish that may have been used on the finish in the past. 10. Allow to dry thoroughly for at least 24 hours.
Removing Deeply Buried Paints
A deeply buried paint can be removed entirely or partially by a simple procedure. This is paint usually left after you have removed the previous cotes with remover or light scraping. Because its so simple its worth trying.
1. Apply a liberal coat of shellac with a brush and let it dry for at least 24 hours.
2. Use the remover as previously directed. All or part of the buried paint will come off with the shellac. Be sure all traces of the remover is gone and the surface is completely dry before applying a new finish.
"visit http://www.kewoodworking.com "
Article Source: [http://EzineArticles.com/?How-to-Remove-Old-Finish-From-Furniture&id=6687448] How to Remove Old Finish From Furniture
Read More..
General Rules for Removing Old Finish
1. Do nothing that will harm the original surface unless the piece is to be painted.
2. If you plan to replace the old finish with a clear type, all old finish must be removed so the new will hold properly.
3. When removing old paint it is not only permissible but acceptable to most collectors that the marks of wear through the years, as well as traces of color from the old paint be allowed to remain so that they will show through the new finish. Traces of old paint add interest to the piece by their variations of color, and are evidence of age. Old paint however, should not be left on in thick patches or blotches.
4. For final cleaning, after using a remover, use a cabinet scraper or knife blade on joints, corners, and angles on flat surfaces. Use steel wool to clean out carvings, turnings, mouldings etc.
5. If the old finish is shellac, you dont need a paint and varnish remover. It can be taken off with denatured alcohol and steel wool.
Selecting Your Paint Remover
Commercial removers are solvents rather than corrosives. They act more slowly on older paints than on new, but they are the only materials that can be used safely. They attack the material such as linseed oils used in paint, or the resins in shellac, varnish, and lacquer. It wont injure a surface by burning it or leaving marks and wont be harmful to glue or raise the grain of the wood. They contain no water and may be used on veneered surfaces without causing the veneer to loosen. When used properly and washed off, solvent-type paint removers leave the surface clean. Dislodging layers of old paint or varnish isnt difficult, but patience, time, and-following the directions on the container are required.
How to Remove Old Finishes
Dislodging layers of old paint or varnish isnt difficult, but it takes patience, time, ans perseverance. Here are some basic directions for using paint remover.
1. Place the piece to be worked on over layers of old newspaper in good strong light, and if possible, with the top surface in a horizontal position. Avoid working in cold temperatures below 68 degrees F--cold slows down the action of removers.
2. Shake the remover thoroughly, pour a small amount into a small can and apply thickly with a full brush in one direction. Do not rebrush.
3. Let the remover stand for a period of from 10 to 20 minutes, or until the paint or varnish lifts.This is indicated by a crinkling of the surface. Do not let the remover dry. If it begins to dry, apply an additional coat and wait for it to act.
4. When the surface covering has lifted, remove it with a dull putty knife that has the corners rounded off. Remove the accumulation of remover and finish and wipe the knife on a piece of old newspaper.
5. Wipe off as much of the remaining finish as possible using burlap squares.
6. Scrub the surface with a small brush dipped in denatured alcohol.
7. Wipe off with several clean cloths.
8. Rub the surface with steel wool dipped in denatured alcohol.
9. Wipe with cloths dipped in alcohol. This not only cleans the traces of remover from the surface but neutralizes its further action. Follow by wiping with clean cloths dipped in turpentine or paint thinner.Then wipe with dry rags. This will remove any remaining wax or silicone polish that may have been used on the finish in the past. 10. Allow to dry thoroughly for at least 24 hours.
Removing Deeply Buried Paints
A deeply buried paint can be removed entirely or partially by a simple procedure. This is paint usually left after you have removed the previous cotes with remover or light scraping. Because its so simple its worth trying.
1. Apply a liberal coat of shellac with a brush and let it dry for at least 24 hours.
2. Use the remover as previously directed. All or part of the buried paint will come off with the shellac. Be sure all traces of the remover is gone and the surface is completely dry before applying a new finish.
"visit http://www.kewoodworking.com "
Article Source: [http://EzineArticles.com/?How-to-Remove-Old-Finish-From-Furniture&id=6687448] How to Remove Old Finish From Furniture
Sunday, March 2, 2014
The Easiest Ever Way To Fix Stained Drawers
Doing laundry. Then, doing more laundry. Oh, and also ironing. Lets not forget that.
However, in between all my domestic responsibities, I was also able to fit in one of the many tasks on my never ending to do list. I was able to finish lining the drawers of a furntiture piece I recently completed. Yay! Ok, this was not really an exciting task, but I got it done.
A couple of weeks ago, I finished a dresser/buffet in a finish I call Two-Toned Glam. The piece came out beautifully in the end, but it had given me little fits here and there. Just little things. For intstance, I talked in an earlier post about having to deal with water marks that had popped up.
Another minor, but nevertheless so very annoying, problem with this piece was a drawer which had a stain. From time to time, I will have a great piece to refinish that may have stains or marks inside the drawers. And, because most of my pieces I sell at my Etsy shop, I want to be sure they go to my customers in good shape. Sometimes, I can clean away marks. Other times, I may need to sand them away. On this piece, however, the stain was too deep and superficial sanding would not work.
So, my favorite, and by far the easiest, fix for imperfect drawers is lining them with adhesive cork.
This brand I purchase right at Home Depot.
It gives a clean and natural look and for drawers that could see a lot of wear, it is very durable. It also "naturally resists mold and mildew, as well as, cushions and protects"...that there is right off the label!
First, I measure the length and width of the drawer. Oh, and take out the drawer to make it easier...which I, of course, did not yet do in this picture.
Then, unroll your cork adhesive onto a flat surface and mark off the drawer measurements on the back grid and cut along the lines.
Next, peel back one corner of the cut liner and lay the adhesive side down in your selected drawer corner.
Once your corner is down, slowly pull the white paper off the adhesive back, working from the first corner. At the same time you are pulling the white paper off, begin pressing down the adhesive side, smoothing as you go.
Here is my drawer "after" with the cork liner. It is a downright pretty inside of a drawer...dont you think?
Tuesday, February 18, 2014
How to Choose The Best Plans Sheds
 |
| Plans Sheds |
Material checklist, The first thing you ought to see about any given pair of plans is a materials list. This particular comes in really handy and may speed up assembling your shed significantly, by permitting you to precut your entire measurements in advance, It can also be utilized to get an notion of how much the work is going to run you in advance. All you need to do will be add every one of the specified table lengths along with calculate the price by looking at a home development stores rates.
Pictures are crucial, Pictures could be a huge aid by allowing you to view the end product ahead of time so that you know what you may anticipate when building your personal backyard shed. Theyre able to give you a far better idea of how a project really should look through different stages of the building course of action, A picture can display you items that regular wording could in no choice explain. I assume the age old expressing "a picture may be worth 1000 words" establishes true in cases like this. Refer to the many pictures through the entire shed building process to you should alchoices be doing every little thing correctly,
Top shots, Level shots are just different aspects of the shed that permit you to get certain measurements along with design aspects right on specific sides in the shed plans.
These needs to have a different watch for each aspect of the shed as well as contain numerous measurements concerning particular particulars on that aspect. For instance, in the event the drawing has been for the entrance of the garden shed, it should include distinct details about the shed door as well as any special specifics in the front in the shed, Having these kinds of will drastically increase your accuracy and reliability and productivity and serve as tips when subsequent any group of diy shed plans.
Step by step instructions, Its not all plans for sheds includes detailed step-by-step guidelines. If they carry out, then this will allow you to build your garden shed, reducing the chances of coming to a mistakes along the choice.
Having these kind of step-by-step instructions could also help someone who doesnt alchoices have as much building knowledge by giving all of them a specific choice to follow. Once they follow this method they will not alchoices be wondering about particular variables that will tend to surface when building the shed. Look for particular shed plans that have step-by-step directions if you arent positive your skills.
How to Pick the best Plans For Storage sheds
Monday, February 17, 2014
Do it Yourself Woodworking Some Tips and Ideas to Start Your Own Woodworking Project
Do it yourself woodworking projects are fun activities that you can do at home and a good alternative to buying brand new furniture. It is also a good way to restore old furniture or make something new out of your furniture that has been stuck in your garage for long. It just takes a little creativity and you can do many projects by yourself.
Even if it is just your first time to do it on your own, you can however find some great resources that you will find useful in making your do it yourself woodworking project successful. You may however start with some simple projects to make it easier to complete. However, here are some tips that you might also find useful in your woodworking project.
-Your choice of wood. One of the things that you may need to decide when starting on a woodworking project is the wood to use. You can choose either softwood or hardwood in your projects or any kind of species depending also of the project you are making. Most often, hardwoods are used for indoor projects like cabinets or furniture and softwood are often for outdoor projects. In fact, softwoods are even used as lumber in most construction projects as they are easy for construction especially when you are using woodworking tools. If you are just starting, it may be wise to start with softwoods to make your project a little easier for you.
- Sanding your wood is also important as this creates a smooth finish to your woodworking project, makes your project durable from wear and tear, and of course allows your painted project to be long-lasting. One of the most important tips in sanding your wood is to go with the grain. Going against it will create marks on your wood and may not look good with the finish or the paint. Also start with the coarse-grit sandpaper down to the finer ones.
- In choosing your woodworking finish, make sure you are using something that fits your do it yourself woodworking project. There are different choices of finish and each of them have distinct properties - oil, varnish, urethane, wax, shellac, lacquers, make sure you know what is best for your project. If you want a tint of orange to your finish product, shellac may be a good choice to enhance the appearance of dark-colored woods. If you are doing an outdoor project, varnish may be suitable for you as this finish is resistant to moisture and solvent and also protects the wood from scratches.
One great tip if you are just starting out with a do it yourself woodworking project is to start with something that you are comfortable working, and from there, you can learn more tips and techniques in your woodworking. It is also important to be extra careful in working with your tools especially in working with your lathes, and make sure you got good quality tools especially if you are looking forward to more woodworking projects in the future.
Even if it is just your first time to do it on your own, you can however find some great resources that you will find useful in making your do it yourself woodworking project successful. You may however start with some simple projects to make it easier to complete. However, here are some tips that you might also find useful in your woodworking project.
-Your choice of wood. One of the things that you may need to decide when starting on a woodworking project is the wood to use. You can choose either softwood or hardwood in your projects or any kind of species depending also of the project you are making. Most often, hardwoods are used for indoor projects like cabinets or furniture and softwood are often for outdoor projects. In fact, softwoods are even used as lumber in most construction projects as they are easy for construction especially when you are using woodworking tools. If you are just starting, it may be wise to start with softwoods to make your project a little easier for you.
- Sanding your wood is also important as this creates a smooth finish to your woodworking project, makes your project durable from wear and tear, and of course allows your painted project to be long-lasting. One of the most important tips in sanding your wood is to go with the grain. Going against it will create marks on your wood and may not look good with the finish or the paint. Also start with the coarse-grit sandpaper down to the finer ones.
- In choosing your woodworking finish, make sure you are using something that fits your do it yourself woodworking project. There are different choices of finish and each of them have distinct properties - oil, varnish, urethane, wax, shellac, lacquers, make sure you know what is best for your project. If you want a tint of orange to your finish product, shellac may be a good choice to enhance the appearance of dark-colored woods. If you are doing an outdoor project, varnish may be suitable for you as this finish is resistant to moisture and solvent and also protects the wood from scratches.
One great tip if you are just starting out with a do it yourself woodworking project is to start with something that you are comfortable working, and from there, you can learn more tips and techniques in your woodworking. It is also important to be extra careful in working with your tools especially in working with your lathes, and make sure you got good quality tools especially if you are looking forward to more woodworking projects in the future.
Thursday, February 6, 2014
How to Build a Campaign Style Desk
On Mondays post I shared a few photos and why this desk wasnt a weekend project and how it could be. Today Ill talk about how we built it. Again, a big thank you to David for doing most of it, I was more of an assistant on this project!
First, we calculated the amount of wood we needed and off we went to Home Depot to pick up our supplies:
1x12 Poplar (about 10)
1x2 Poplar (about 48 - we made a second trip for more wood, so I think this is about right :)
For those not familiar with American terminology for wood, for some reason a 1x12 isnt actually 1" tall x 12" wide it is really 3/4" tall x 11 1/4" wide. Same applies for other sizes too, like a 1x2 is really 3/4" x 1 1/2". I know, weird. Just wanted to go over that upfront since I talk about measurements below :)
Anyways, total for the wood was around $100
We also needed:
Brass Screws
Wood Glue
Then the two 1x12s were cut and glued together and held with a clamp. Once dry, 5 supports were cut out of 1x2 poplar, the same width as the top and attached to the bottom of the desk with glue and screws and clamped to dry (The last support should be snug against the leg so make sure to account for that- see photos towards end of post). Then 1x2s were cut at a 45 to make the outer frame, glued and then clamped in place to dry. If you have any gaps use a small amount of wood filler to fill them.
After everything had dried, all the edges and where the wood meets was sanded with the orbital sander (120 and then 220 grit)
Next, we calculated the angle of the X legs. On the table, we started at the edge of the 1x12 (not the very end at the trim) and measured 29.25" for a 30" standard desk height accounting for the .75 top too. We laid two 1x2s on top of each other in an x on the desk top. Lining the top board with the outside of the trim and the bottom with the inside of the trim. We marked with a pencil where the boards intersect in the middle and a straight line at the top and bottom.
Next we cut the angles (which were just marked) for the top and bottom for eight boards (4 for each x-leg). We then cut the center sections (drawn where the legs cross making the X) on four of the boards.
If you use a wood like poplar with a lot of variety in color and grain, you will want to spend some time to match similar boards for each leg.
Last, we cut a 1.5 inch section out of the inner rear leg to later attach the center brace.
Now to assemble the legs! We applied wood glue to all of the pieces, clamped them together and screwed them from the inside. We assembled the four pieces as shown below and then sanded them to make sure the connections were seamless.
After sanding, we applied glue and screwed the individual legs together creating the X.
Once the X sides were complete, we applied glue to the corners and sides and set them in place.
For extra support, we added wood angles to lock the legs in place. David cut a few angles to find the perfect fit and then cut the angle so it would sit flush with the trim. it was glued and clamped in place.
After the legs were set, the center brace (going between the X sides) was glued into place. The center brace was constructed of two 1x2s cut to the width of the table minus three inches (for the trim and outer board of the x-leg)
And that was it! You can see that we used a combination of wood glue and hidden (or less noticeable screws) for the construction. As long as the wood glue dries thoroughly and is clamped to dry, it is very strong! For areas that have more stress, like the legs and table top center supports, we also used screws in addition to the wood glue. Ill take more photos once we have the office complete, but since I took the photos, I also have my large Mac desktop on top and it is very solid.
I love the grain of the poplar! It probably isnt for everyone, in fact as I was looking at hardwoods online, I saw some references to it as the ugly hardwood. The nerve! Im thinking they were referencing the extreme difference in grains ... so it does take more time to pick out ones that are similar.
The desktop looks like one piece of wood because we chose wood where the grain would match, also sanding it until it was smooth helped even out the line.
I think the legs look pretty seamless too ...
If we were building this again, I probably would use oak due to it taking less time in sanding, see Mondays post for my full explanation of why wasnt a weekend project and how to turn it into one!
The total cost was around $100 for wood and about $10 more for screws and wood glue if not already owned. So about $100 cheaper than the World Market equivalent
Im off to get supplies and work on my next project ... follow me on instagram @sarahmdorseydesigns for sneak peaks!
Wednesday, January 29, 2014
Description who had the idea to build the wooden horse
This who had the idea to build the wooden horse
Trojan horse - wikipedia, the free encyclopedia, According to quintus smyrnaeus, odysseus thought of building a great wooden horse (the horse being the emblem of troy), hiding an elite force inside, and fooling the. History of the trojan war - stanford university, The tro jan war. the apple of discord; greek armament; finding troy; embassy to priam; the war; the trojan horse; after the war. the apple of discord. the trojan war.
John wooden: the difference between winning and succeeding, With profound simplicity, coach john wooden redefines success and urges us all to pursue the best in ourselves. in this inspiring talk he shares the advice he gave. 101 romantic ideas - scribd, This is a free bonus version of 101 romantic ideas. feel free to forward to or make copies for your friends. theromantic.com 101 romantic ideas. The idea room - inspiring mothers, women and families, It’s here!! i have had several of you asking for the new challenge and i am happy to say it is here! i thought i would change things up a bit and that it would be. 20 creative ways to upcycle pallets in your garden |, 20 inspiring diy ideas for upcycling wooden pallets in your garden including vertical gardens, planters, greenhouses, compost bays, raised garden beds & more. Put - definition of put by the free online dictionary, Put (po͝ot) v. put, put·ting, puts. v.tr. 1. to place in a specified location; set: she put the books on the table. 2. to cause to be in a specified condition: his. The barefoot agrarian | cheap&dirty: build a firewood shed, This firewood shed was built from free wooden pallets, scrap wood, and a few items from the big box store..
who had the idea to build the wooden horse its good
who had the idea to build the wooden horse ,
Subscribe to:
Posts (Atom)